pattern
Mehr aus
Polymer.
pattern

KEBAFLEX – H / SPAS 50 A.02 natural

TPE-S, Shore A50, modified for good adhesion to polyamides such as PA6, PA66, PA12 or partially aromatic PA grades such as GRIVORY GV (manufacturer EMS-GRIVORY)



TPE-S - KEBAFLEX / S

Details

Under the trade name KEBAFLEX / S we market a range of thermoplastic elastomer compounds based on SEBS/PP. KEBAFLEX / S is available in various Shore hardnesses from below A10 to above D50 and is often used as a substitute for rubber due to its cost-effective processing by injection molding. It is soft and flexible, freely colorable, shows good elastic behavior up to 100°C and offers a pleasant feel. A wide range of modified compounds is available, e.g. adhesion-modified grades for 2K injection molding, printable grades, grades with optimized compression set, etc.



ISO designation

  • TPS-SEBS


Typical areas of application

  • Sealing elements
  • Seals
  • Handles
  • Haptic components


Industry sectors

  • Automotive
  • Electrical and electronics industry
  • Household appliances
  • Industry
  • Mechanical Engineering
  • Furniture industry
  • Sports & Recreation


properties

  • flexible
  • good haptics
  • adhesion modified
  • semi-crystalline
  • weich

Overview of product features

Physical properties

Density in kg/m³
ISO 1183-1
910.00

Mechanical properties

Breaking stress in MPa
ISO 527-1
3.4
Elongation at break in %
ISO 527-1
450.0
Shore A hardness
DIN ISO 7619-1
50
Stress at 10% elongation in MPa
DIN EN ISO 527-1
0.50
Stress at 50% elongation in MPa
DIN EN ISO 527-1
1.10
Stress at 100% elongation in MPa
DIN EN ISO 527-1
1.60
Stress at 300% elongation in MPa
DIN EN ISO 527-1
3.00

Thermal properties

Fire behavior (0.4 mm wall thickness)
IEC 60695-11-10
HB
Fire behavior (0.8 mm wall thickness)
IEC 60695-11-10
HB
Fire behavior (1.6 mm wall thickness)
IEC 60695-11-10
HB
Fire behavior (3.2 mm wall thickness)
IEC 60695-11-10
HB

Pre-drying:

Dryer type: dry air dryer
Temperature: 80°C
Drying time: 3 – 4 h
Residual moisture: < 0.02%.

Temperatures:

Melt temperature: 230 – 250°C
Mold temperature: 40 – 60 °C

General processing notes:

The relatively high viscosity requires high injection speeds and medium injection pressure. To avoid high internal stresses, and to improve the 2K adhesion, the holding pressure should be kept as low as possible, and the holding times of injection pressure and holding pressure should be as short as possible.

A compound temperature at the upper limit also improves adhesion.

Very good venting of the cavity is a basic prerequisite for achieving a high injection speed and, consequently, good adhesion and a good surface quality.

Legal notice

The information in this data sheet is based on our current knowledge and experience. Due to the wide range of possible influences during processing and application of our products, they do not exempt the processor from carrying out his own tests and trials. A legally binding assurance of certain properties or suitability for a specific application cannot be derived from our information.

* FE products are development products which are still in the trial phase. Technical data may still change in the course of product and process development. No final decision has yet been made on the commercialization of FE products. We reserve the right to discontinue the manufacture of FE products without giving further reasons.

pattern

Do you have
questions about our
products or services?

Then make an appointment with us.
Our team will be happy to advise you in a
personal conversation or by e-mail.

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
HelloHand
We are happy to help if you have any questions about our products or services
Your request

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Send request
Send request
Subscribe to newsletter

Would you like to use our service and always stay up to date? Simply subscribe to our newsletter.

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Cookie-Einstellungen
Auf dieser Website werden Cookie verwendet. Diese werden für den Betrieb der Website benötigt oder helfen uns dabei, die Website zu verbessern.
Alle Cookies zulassen
Auswahl speichern
Individuelle Einstellungen
Individuelle Einstellungen
Dies ist eine Übersicht aller Cookies, die auf der Website verwendet werden. Sie haben die Möglichkeit, individuelle Cookie-Einstellungen vorzunehmen. Geben Sie einzelnen Cookies oder ganzen Gruppen Ihre Einwilligung. Essentielle Cookies lassen sich nicht deaktivieren.
Speichern
Abbrechen
Essenziell (1)
Essenzielle Cookies werden für die grundlegende Funktionalität der Website benötigt.
Cookies anzeigen
Statistik (2)
Statistik Cookies tracken den Nutzer und das dazugehörige Surfverhalten um die Nutzererfahrung zu verbessern.
Cookies anzeigen