pattern
Mehr aus
Polymer.
pattern

KEBATRON PPS L1030C1 black

KEBATRON PPS L1030C1 black is an electrically conductive, 30% carbon fiber reinforced PPS compound.



PPS - KEBATRON

Details

Under the trade name KEBATRON, we offer a range of high-performance compounds based on PPS. KEBATRON offers high continuous service temperature, good aging behavior, high strength and stiffness, is inherently flame retardant and has exceptionally good chemical resistance.



ISO designation

  • PPS-L-CF30


Typical areas of application

  • Valve caps
  • Distributor
  • Fasteners
  • Gears
  • Housing
  • Sliding elements
  • Plain bearing
  • Piston
  • Couplings
  • Bearing bushes
  • Pumps and motors
  • Pump housing
  • Sensors
  • Bobbin
  • Structural components
  • Transport chains
  • Valves


Industry sectors

  • Automotive
  • Electrical and electronics industry
  • Household appliances
  • Industry
  • Aviation Industry
  • Mechanical Engineering
  • Sports & Recreation


properties

  • antistatic
  • dimensionally stable
  • electrically conductive
  • good chemical resistance
  • good aging behavior
  • good fire behavior
  • high continuous used temperature
  • High strength
  • High stiffness
  • High wear resistance
  • semi-crystalline

Overview of product features

Physical properties

Water absorption in %
in Anlehnung an ISO 62
0.02
Density in kg/m³
ISO 1183-1
1460.00

Mechanical properties

Breaking stress in MPa
ISO 527-1
235.0
Elongation at break in %
ISO 527-1
1.4
Notched impact strength (Charpy) at 23°C in kJ/m²
ISO 179-1eA
5.8

Rheological properties

Shrinkage in flow direction in %
ISO 294-4
0.10
Shrinkage transverse to the flow direction in %
ISO 294-4
0.50

Thermal properties

Melting temperature (DSC, 10°C/min) in °C
ISO 11357-1/-3
278.0
Heat deflection temperature HDT (1.80 MPa) in °C
ISO 75-1/-2
260.0
Fire behavior (1.6 mm wall thickness)
IEC 60695-11-10
V-0
Glass transition temperature in °C
DIN EN ISO 11357-1
90

Electrical properties

Contact resistance in Ohm*m
IEC 60093
1e-1

Pre-drying:

Dryer type: dry air dryer (!).
Temperature: 120 – 140 °C
drying time: 4 – 8 h
Recommended max. residual moisture: < 0.02 %.

Recommended basic settings:

melt temperature: 320 – 340°C
Mold temperature: 140 – 180°C (As a rule of thumb, the higher the requirements, the higher the mold temperature).
Back pressure: < 10 bar (spec.)

The injection speed should be set as a slow – fast – slow profile. As a principle: as fast as possible, as slow as necessary.

Machine selection:

In the processing of KEBATRON PPS, wear- and corrosion-protected injection units have proven their worth. The injection unit should be selected so that the shot volume is 50 – 80% of the maximum metering volume. The dwell time should be kept as short as possible.

Legal notice

The information in this data sheet is based on our current knowledge and experience. Due to the wide range of possible influences during processing and application of our products, they do not exempt the processor from carrying out his own tests and trials. A legally binding assurance of certain properties or suitability for a specific application cannot be derived from our information.

* FE products are development products which are still in the trial phase. Technical data may still change in the course of product and process development. No final decision has yet been made on the commercialization of FE products. We reserve the right to discontinue the manufacture of FE products without giving further reasons.

pattern

Do you have
questions about our
products or services?

Then make an appointment with us.
Our team will be happy to advise you in a
personal conversation or by e-mail.

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
HelloHand
We are happy to help if you have any questions about our products or services
Your request

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Send request
Send request
Subscribe to newsletter

Would you like to use our service and always stay up to date? Simply subscribe to our newsletter.

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Cookie-Einstellungen
Auf dieser Website werden Cookie verwendet. Diese werden für den Betrieb der Website benötigt oder helfen uns dabei, die Website zu verbessern.
Alle Cookies zulassen
Auswahl speichern
Individuelle Einstellungen
Individuelle Einstellungen
Dies ist eine Übersicht aller Cookies, die auf der Website verwendet werden. Sie haben die Möglichkeit, individuelle Cookie-Einstellungen vorzunehmen. Geben Sie einzelnen Cookies oder ganzen Gruppen Ihre Einwilligung. Essentielle Cookies lassen sich nicht deaktivieren.
Speichern
Abbrechen
Essenziell (1)
Essenzielle Cookies werden für die grundlegende Funktionalität der Website benötigt.
Cookies anzeigen
Statistik (2)
Statistik Cookies tracken den Nutzer und das dazugehörige Surfverhalten um die Nutzererfahrung zu verbessern.
Cookies anzeigen