pattern
Mehr aus
Polymer.
pattern

KEBAFORM C 901 FA

POM copolymer unreinforced, medium viscosity, reduced formaldehyde emission for automotive interior applications



POM - KEBAFORM

Details

Under the trade name KEBAFORM, we market a wide product range of POM copolymers. KEBAFORM products are characterized by high strength and surface hardness, excellent chemical resistance and outstanding sliding and wear behavior. The product range includes basic grades with different viscosities, sliding and wear-optimized grades, variants reinforced with glass and carbon fibers, and various other modified compounds.



ISO designation

  • POM-C


Typical areas of application

  • Controls
  • Fasteners
  • Spring elements
  • Housing
  • Sliding elements
  • Plain bearing
  • Rollers
  • Valves
  • Connecting elements
  • Gears


Industry sectors

  • Automotive


properties

  • dimensionally stable
  • low-emission
  • good chemical resistance
  • good gliding properties
  • High strength
  • High wear resistance
  • semi-crystalline

Overview of product features

Physical properties

Moisture absorption 23°C/50% r.h. in %.
in Anlehnung an ISO 62
0.22
Density in kg/m³
ISO 1183-1
1410.00

Mechanical properties

E-modulus in MPa
ISO 527-1
2700
Yield stress in MPa
ISO 527-1
65
Elongation at yield in %
ISO 527-1
9.0
Impact strength (Charpy) at 23°C in kJ/m²
ISO 179-1eU
100.0
Notched impact strength (Charpy) at 23°C in kJ/m²
ISO 179-1eA
7.0

Rheological properties

Melt flow rate MFR (test condition)
190°C / 2,16kg
Melt flow rate MFR in g/10min
ISO 1133
9.0
Shrinkage in flow direction in %
ISO 294-4
2.00
Shrinkage transverse to the flow direction in %
ISO 294-4
2.00

Thermal properties

Melting temperature (DSC, 10°C/min) in °C
ISO 11357-1/-3
166.0
Heat deflection temperature HDT (1.80 MPa) in °C
ISO 75-1/-2
110.0
Heat deflection temperature HDT (0.45 MPa) in °C
ISO 75-1/-2
160.0
Coefficient of thermal expansion in flow direction in E-6/K
ISO 11359-1/-2
120.0
Coefficient of thermal expansion transverse to the flow direction in E-6/K
ISO 11359-1/-2
120.0
Fire behavior (0.8 mm wall thickness)
IEC 60695-11-10
HB

Electrical properties

Contact resistance in Ohm*m
IEC 60093
1e+16
Surface resistivity in ohms
IEC 60093
1e+16

Pre-drying:

(May be required to remove surface moisture:)
Dryer type: Dry air dryer
Temperature: 80 – 100°C
Drying time: 2 – 4 h

Temperatures:

Mass temperature: 180 – 210°C
Mold temperature: 60 – 120°C (general guideline for technical parts: min. 90°C)
Back pressure (spec.): 10 – 40 bar
Injection speed: medium
Injection pressure: 600 – 1200 bar (depending on part and gate geometry)
Holding pressure: 600 – 1200 bar (depending on part and gate geometry)

General processing instructions:

The residence time of the melt in the screw antechamber should be kept as short as possible. In case of longer downtimes, an empty spraying of barrel and hot runner is necessary.

Legal notice

The information in this data sheet is based on our current knowledge and experience. Due to the wide range of possible influences during processing and application of our products, they do not exempt the processor from carrying out his own tests and trials. A legally binding assurance of certain properties or suitability for a specific application cannot be derived from our information.

* FE products are development products which are still in the trial phase. Technical data may still change in the course of product and process development. No final decision has yet been made on the commercialization of FE products. We reserve the right to discontinue the manufacture of FE products without giving further reasons.

pattern

Do you have
questions about our
products or services?

Then make an appointment with us.
Our team will be happy to advise you in a
personal conversation or by e-mail.

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
HelloHand
We are happy to help if you have any questions about our products or services
Your request

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Send request
Send request
Subscribe to newsletter

Would you like to use our service and always stay up to date? Simply subscribe to our newsletter.

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Cookie-Einstellungen
Auf dieser Website werden Cookie verwendet. Diese werden für den Betrieb der Website benötigt oder helfen uns dabei, die Website zu verbessern.
Alle Cookies zulassen
Auswahl speichern
Individuelle Einstellungen
Individuelle Einstellungen
Dies ist eine Übersicht aller Cookies, die auf der Website verwendet werden. Sie haben die Möglichkeit, individuelle Cookie-Einstellungen vorzunehmen. Geben Sie einzelnen Cookies oder ganzen Gruppen Ihre Einwilligung. Essentielle Cookies lassen sich nicht deaktivieren.
Speichern
Abbrechen
Essenziell (1)
Essenzielle Cookies werden für die grundlegende Funktionalität der Website benötigt.
Cookies anzeigen
Statistik (2)
Statistik Cookies tracken den Nutzer und das dazugehörige Surfverhalten um die Nutzererfahrung zu verbessern.
Cookies anzeigen