pattern
Mehr aus
Polymer.
pattern

KEBABLEND / M FE 161101 PA12 (Development product)*

KEBABLEND / M FE 161101 is a development product based on PA12 for the production of injection molded magnets. Due to the high degree of filling with rare earths (SmCo), KEBABLEND /M FE 161101 enables the injection molding production of very powerful magnets.



PA 12 - KEBABLEND

Details

KEBABLEND is a wide range of functional compounds, often tailor-made to customer requirements. Under the trade name KEBABLEND, we market magnetizable, thermally or electrically conductive compounds, high-density injection molding materials, compounds for radiation protection applications, detectable plastics and much more.



ISO designation

  • PA12-MED


Typical areas of application

  • Spring elements
  • Holding magnets
  • Couplings
  • Magnets for sensors
  • Pumps and motors
  • Rotors
  • Switch
  • Valves


Industry sectors

  • Automotive
  • Electrical and electronics industry
  • Household appliances
  • Mechanical Engineering
  • Furniture industry
  • Sports & Recreation


properties

  • dimensionally stable
  • magnetizable
  • semi-crystalline

Overview of product features

Mechanical properties

Breaking stress in MPa
ISO 527-1
80.0

Rheological properties

Melt flow rate MFR (test condition)
270°C / 5,0kg
Melt flow rate MFR in g/10min
ISO 1133
150.0

Thermal properties

Melting temperature (DSC, 10°C/min) in °C
ISO 11357-1/-3
178.0
Fire behavior (0.4 mm wall thickness)
IEC 60695-11-10
HB
Fire behavior (0.8 mm wall thickness)
IEC 60695-11-10
HB
Fire behavior (1.6 mm wall thickness)
IEC 60695-11-10
HB
Fire behavior (3.2 mm wall thickness)
IEC 60695-11-10
HB

Magnetic properties

Remanence (Br) in mT
DIN EN 60404-5
660
Coercivity (jHc) in kA/m
DIN EN 60404-5
880
max. energy product (BH max) in kJ/m³
DIN EN 60404-5
82.0

Pre-drying:

Dryer type: dry air dryer
Temperature: 80°C
Drying time: 4-8 h

Recommended basic settings:

Melt temperature: 260 – 280°C
Mold temperature: 60 – 80 °C
Injection speed: medium – high
Back pressure: 40 – 80bar (spec.)

Machine selection:

Screw: special injection units for magnetic compounds; low compression screws with non-return valve
Nozzle: Open nozzle
Wear protection: Wear and corrosion protected according to machine manufacturer’s recommendation suitable for processing magnetic compounds
Injection unit: Shot volume = 50-80% of maximum metering volume

Further important processing information:

The residence time of the melt in the screw antechamber should be kept as short as possible. If this is not observed, segregation can occur due to the large difference in density between the filler and the substrate if the downtimes are too high. The ideal here is metering time = cooling time. A medium back pressure leads to optimum homogenization. Due to the high filler content, the spraying equipment must be equipped with wear and corrosion protection.

Legal notice

The information in this data sheet is based on our current knowledge and experience. Due to the wide range of possible influences during processing and application of our products, they do not exempt the processor from carrying out his own tests and trials. A legally binding assurance of certain properties or suitability for a specific application cannot be derived from our information.

* FE products are development products which are still in the trial phase. Technical data may still change in the course of product and process development. No final decision has yet been made on the commercialization of FE products. We reserve the right to discontinue the manufacture of FE products without giving further reasons.

pattern

Do you have
questions about our
products or services?

Then make an appointment with us.
Our team will be happy to advise you in a
personal conversation or by e-mail.

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
HelloHand
We are happy to help if you have any questions about our products or services
Your request

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Send request
Send request
Subscribe to newsletter

Would you like to use our service and always stay up to date? Simply subscribe to our newsletter.

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Cookie-Einstellungen
Auf dieser Website werden Cookie verwendet. Diese werden für den Betrieb der Website benötigt oder helfen uns dabei, die Website zu verbessern.
Alle Cookies zulassen
Auswahl speichern
Individuelle Einstellungen
Individuelle Einstellungen
Dies ist eine Übersicht aller Cookies, die auf der Website verwendet werden. Sie haben die Möglichkeit, individuelle Cookie-Einstellungen vorzunehmen. Geben Sie einzelnen Cookies oder ganzen Gruppen Ihre Einwilligung. Essentielle Cookies lassen sich nicht deaktivieren.
Speichern
Abbrechen
Essenziell (1)
Essenzielle Cookies werden für die grundlegende Funktionalität der Website benötigt.
Cookies anzeigen
Statistik (2)
Statistik Cookies tracken den Nutzer und das dazugehörige Surfverhalten um die Nutzererfahrung zu verbessern.
Cookies anzeigen