Mehr aus

KEBABLEND / M 48/67 PA12

PA12, functional compound for the production of plastic bonded magnets. Due to the high filler content of rare earths, KEBABLEND /M 48/67 PA12 enables the injection molding of very powerful magnets.



KEBABLEND is a wide range of functional compounds, often tailor-made to customer requirements. Under the trade name KEBABLEND, we market magnetizable, thermally or electrically conductive compounds, high-density injection molding materials, compounds for radiation protection applications, detectable plastics and much more.

ISO designation

  • PA12-MED

Typical areas of application

  • Holding magnets
  • Magnets for sensors
  • Pumps and motors

Industry sectors

  • Automotive
  • Electrical and electronics industry
  • Household appliances
  • Mechanical Engineering
  • Sanitary industry


  • dimensionally stable
  • magnetizable

Overview of product features

Magnetic properties

Remanence (Br) in mT
DIN EN 60404-5
Coercivity (jHc) in kA/m
DIN EN 60404-5
max. energy product (BH max) in kJ/m³
DIN EN 60404-5

Mechanical properties

E-modulus in MPa
ISO 527-1
Breaking stress in MPa
ISO 527-1
Elongation at break in %
ISO 527-1

Physical properties

Density in kg/m³
ISO 1183-1

Rheological properties

Shrinkage in flow direction in %
ISO 294-4
Shrinkage transverse to the flow direction in %
ISO 294-4

Thermal properties

Melting temperature (DSC, 10°C/min) in °C
ISO 11357-1/-3

Pre-drying may be necessary to achieve perfect processability in the injection molding process:


Dryer type: dry air dryer
Temperature: 80 °C
Drying time: 3-6 h

Recommended basic settings:

Melt temperature: 260 – 280 °C
Mold temperature: 60 – 80 °C
Injection speed: medium – high
Back pressure: 40 – 80bar (spec.)

Machine selection:

Screw: special injection units for magnetic compounds; low compression screws with non-return valve
Nozzle: Open nozzle
Wear protection: Wear and corrosion protected according to machine manufacturer’s recommendation suitable for processing magnetic compounds
Injection unit: Shot volume = 50 – 80% of the maximum metering volume

Further important processing information:

The residence time of the melt in the screw antechamber should be kept as short as possible. If this is not observed, segregation can occur due to the large difference in density between the filler and the carrier material if the downtimes are too high. The ideal here is metering time = cooling time. A medium back pressure leads to optimum homogenization. Due to the high filler content, the spraying equipment must be equipped with wear and corrosion protection.

Legal notice

The information in this data sheet is based on our current knowledge and experience. Due to the wide range of possible influences during processing and application of our products, they do not exempt the processor from carrying out his own tests and trials. A legally binding assurance of certain properties or suitability for a specific application cannot be derived from our information.

* FE products are development products which are still in the trial phase. Technical data may still change in the course of product and process development. No final decision has yet been made on the commercialization of FE products. We reserve the right to discontinue the manufacture of FE products without giving further reasons.


Do you have
questions about our
products or services?

Then make an appointment with us.
Our team will be happy to advise you in a
personal conversation or by e-mail.

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us:
We are happy to help if you have any questions about our products or services
Your request

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us:
Send request
Send request
Subscribe to newsletter

Would you like to use our service and always stay up to date? Simply subscribe to our newsletter.

Your request has been sent.
Your request could not be sent. Please try again or email us:
Auf dieser Website werden Cookie verwendet. Diese werden für den Betrieb der Website benötigt oder helfen uns dabei, die Website zu verbessern.
Alle Cookies zulassen
Auswahl speichern
Individuelle Einstellungen
Individuelle Einstellungen
Dies ist eine Übersicht aller Cookies, die auf der Website verwendet werden. Sie haben die Möglichkeit, individuelle Cookie-Einstellungen vorzunehmen. Geben Sie einzelnen Cookies oder ganzen Gruppen Ihre Einwilligung. Essentielle Cookies lassen sich nicht deaktivieren.
Essenziell (1)
Essenzielle Cookies werden für die grundlegende Funktionalität der Website benötigt.
Cookies anzeigen
Statistik (1)
Statistik Cookies tracken den Nutzer und das dazugehörige Surfverhalten um die Nutzererfahrung zu verbessern.
Cookies anzeigen