pattern
Mehr aus
Polymer.
pattern

KEBABLEND / EC FE 170501 PBT (Development product*)

PBT functional compound, electrically conductive



PBT - KEBABLEND

Details

KEBABLEND is a wide range of functional compounds, often tailor-made to customer requirements. Under the trade name KEBABLEND, we market magnetizable, thermally or electrically conductive compounds, high-density injection molding materials, compounds for radiation protection applications, detectable plastics and much more.



ISO designation

  • PBT-CF20


Typical areas of application

  • Housing
  • Sliding elements
  • Bearing bushes
  • Structural components


Industry sectors

  • Automotive
  • Railroad industry
  • Electrical and electronics industry
  • Industry
  • Agriculture
  • Mechanical Engineering
  • Furniture industry
  • Sports & Recreation


properties

  • dimensionally stable
  • electrically conductive
  • good chemical resistance
  • good aging behavior
  • high continuous used temperature
  • High strength
  • High stiffness
  • semi-crystalline

Overview of product features

Physical properties

Density in kg/m³
ISO 1183-1
1360.00

Mechanical properties

E-modulus in MPa
ISO 527-1
12000
Breaking stress in MPa
ISO 527-1
105.0
Elongation at break in %
ISO 527-1
2.3
Impact strength (Charpy) at 23°C in kJ/m²
ISO 179-1eU
30.0

Thermal properties

Melting temperature (DSC, 10°C/min) in °C
ISO 11357-1/-3
225.0
Continuous operating temperature in °C
ISO 2578
130.0
Maximum service temperature (short-term) in °C
ISO 2578
160.0
Fire behavior (0.8 mm wall thickness)
IEC 60695-11-10
HB

Electrical properties

Contact resistance in Ohm*m
IEC 60093
1e+1
Surface resistivity in ohms
IEC 60093
1e+1

Pre-drying:

Dryer type: dry air dryer
Temperature: 80°C
Drying time: 4 – 8 h
Moisture content during processing: < 0.02%.

Recommended basic settings:

Melt temperature: 250 – 260°C
Mold temperature: 90 – 120°C
Injection speed: high
Back pressure: 40 – 80bar (spec.)

Machine selection:

Screw: 3-zone screw with non-return valve
Nozzle: Open nozzle or shut-off nozzle
Wear protection: Wear protected according to machine manufacturer’s recommendation, suitable for processing fiber reinforced plastics
Injection unit: Shot volume = 50-80% of the maximum metering volume

Legal notice

The information in this data sheet is based on our current knowledge and experience. Due to the wide range of possible influences during processing and application of our products, they do not exempt the processor from carrying out his own tests and trials. A legally binding assurance of certain properties or suitability for a specific application cannot be derived from our information.

* FE products are development products which are still in the trial phase. Technical data may still change in the course of product and process development. No final decision has yet been made on the commercialization of FE products. We reserve the right to discontinue the manufacture of FE products without giving further reasons.

pattern

Do you have
questions about our
products or services?

Then make an appointment with us.
Our team will be happy to advise you in a
personal conversation or by e-mail.

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
HelloHand
We are happy to help if you have any questions about our products or services
Your request

You have data to review? Please upload as PDF, JPG and or common 3D file. The data should not exceed the max. size of 30 MB

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Send request
Send request
Subscribe to newsletter

Would you like to use our service and always stay up to date? Simply subscribe to our newsletter.

Your request has been sent.
Your request could not be sent. Please try again or email us: kontakt@barlog.de.
Cookie-Einstellungen
Auf dieser Website werden Cookie verwendet. Diese werden für den Betrieb der Website benötigt oder helfen uns dabei, die Website zu verbessern.
Alle Cookies zulassen
Auswahl speichern
Individuelle Einstellungen
Individuelle Einstellungen
Dies ist eine Übersicht aller Cookies, die auf der Website verwendet werden. Sie haben die Möglichkeit, individuelle Cookie-Einstellungen vorzunehmen. Geben Sie einzelnen Cookies oder ganzen Gruppen Ihre Einwilligung. Essentielle Cookies lassen sich nicht deaktivieren.
Speichern
Abbrechen
Essenziell (1)
Essenzielle Cookies werden für die grundlegende Funktionalität der Website benötigt.
Cookies anzeigen
Statistik (2)
Statistik Cookies tracken den Nutzer und das dazugehörige Surfverhalten um die Nutzererfahrung zu verbessern.
Cookies anzeigen